Renlon operative spraying RenStrength onto a soffit
RenStrengthType A waterproofing system

Fix failed waterproofing without hacking it off

RenStrength™ is our own Type A system for basements, vaults and slabs where the existing waterproofing has failed. Where suitable, it goes straight over the old system and strengthens the structure in the same slim application.

Specifying it? Technical downloads
Over the old system, not after it

Same basement, without the strip-out

Vaulted basement after RenStrength, with clean, even rendered walls and arches
Vaulted basement before RenStrength, with stained, patchy walls and exposed brick

Drag to compare before and after.

RenStrengthOnly from Renlon

Fixes failed waterproofing over what's already there, where suitable.

  • Goes straight over existing render, concrete or bonded screeds, where suitable
  • A faster, cleaner installation with minimal waste
  • Waterproofing and carbon-fibre strengthening in one application
The usual fix

What most remedial jobs start with.

  • Hack off the old render or failed tanking first
  • Strip-out, skips and dust before any new work starts
  • Waterproofing and strengthening let as separate packages
Why choose it

What it gives contractors and specifiers

For contractors and developers

No hacking off, so the programme is shorter

Where suitable, RenStrength™ goes straight over the existing system. There is far less to break out and take away before the new work starts.

  • Protects the programme. No hacking off or strip-out where suitable, so the installation is faster and cleaner.
  • Keeps lettable floor space. A wall build-up of about 12 mm preserves usable internal floor area.
  • Two packages in one. Type A waterproofing and carbon-fibre strengthening in a single application, from one contractor.
  • Protects the substrate. No hacking off, so no damaged brickwork to repair afterwards.
About 12 mmwall build-up
Renlon operative spraying RenStrength onto a soffit
RenStrength™ going onto a soffit
For architects, engineers and surveyors

Tested figures, and one firm responsible for the design

The data you need to specify it, and a specialist who takes responsibility for the waterproofing design.

  • Tested performance. Over 7 bar water resistance and a Euroclass A1/A2 fire rating.
  • The standards. A BS 8102 Type A system. Its render meets EN 1504-9 and EN 1504-3 (class R2).
  • Design responsibility. We take specialist design responsibility, backed by £10m PI insurance.
  • One team accountable. Surveyed, specified and installed by Renlon, with our 10-year guarantee on qualifying works.
Over 7 barwater resistance
Renlon installer fixing carbon fibre mesh to a soffit
Carbon fibre mesh on a soffit
Sustainability

Lower carbon, and far less waste

Where the existing render or screed is sound, RenStrength™ keeps it in place and goes over it.

  • Lower carbon. Keeping what is there cuts the carbon impact of breaking out, carting away and replacing it.
  • Less waste. Existing render and bonded screeds stay in place, so far fewer skips leave site.
  • A cleaner site. Much less noise and dust than hacking off, for the people working and living nearby.
No strip-outwhere the existing system is sound
Renlon operative working on a concrete soffit
A RenStrength™ job in progress
C1
C1 · Active water stopStops persistent leaks, even under pressure.
One slim application

What goes into the 12 mm

Four components are built up in one application, so the wall or soffit is waterproofed and strengthened without giving up floor space.

Scroll through each component below.

C1 · Active water stop

Stops persistent leaks, even under pressure, so the next coats can go on.

Prepared concrete substrate

C2 · Reactive waterproof slurry

Forms a self-healing waterproof barrier.

C2 waterproof slurry coat

C3 · Fibre-reinforced render

A high-strength render for a hard-wearing finish.

C3 render finish

C4 · Carbon or glass-fibre mesh

Improves resistance to cracking and strengthens the structure.

C4 carbon fibre mesh
Where it works

Below ground, on what’s already there

There’s a version of RenStrength for each of these surfaces. Your surveyor checks the structure on the survey and specifies the one that suits it.

Where RenStrength works

Four kinds of surface, each with its own version

Where RenStrength works
SurfaceIt goes overWhy it suits
Concrete wallsExisting concrete.Where no repairs or fairing coats are needed.
Existing renderRender that is already on the wall.The old render doesn’t need hacking off.
Vaults and soffitsPorous or poor soffits such as clinker, Yorkstone or filler-joist concrete.The mesh also strengthens a fragile soffit.
Slabs and screedsExisting slabs or fully bonded screeds.It avoids taking the screed up.
Why trust it

Proven on London projects

  • Beyond 7 barThe waterproof barrier at its core resists water pressure beyond 7 bar.
  • 10-year guaranteeRenlon’s own guarantee on qualifying works.
  • Installed only by RenlonApplied only by Renlon Approved Installers.
Also used on
  • Avery Row
  • Hamilton Terrace
  • 415–419 Oxford Street
  • 200 Strand
  • 31 Great Marlborough Street
FAQ

RenStrength Questions

Quick answers from our surveyors. Still stuck? Email survey@renlon.com and a qualified surveyor replies.

Talk to a surveyor

Reply within one business day

020 8687 4000

Mon to Fri, 8am to 4pm

Does the old render or tanking have to be hacked off?

Often not. RenStrength has variations made to go over existing concrete, existing render and existing slabs or fully bonded screeds. The surface must be sound, so any debonded patches are cut out and replaced first. Your surveyor confirms what can stay on the survey.

How thick is it?

On walls and soffits, about 12 mm in total. Over slabs it is a 30 mm or 50 mm application, depending on the variation.

Is RenStrength a Type A system?

Yes. It is a barrier system bonded to the structure, which BS 8102 calls Type A. Our surveyors design the waterproofing to BS 8102:2022 and say whether it needs to work alongside other protection.

How does it strengthen the structure?

The system includes a carbon or glass-fibre mesh, which improves resistance to cracking and structural degradation. It can also encapsulate steel beams. Any structural calculations are approved by a structural engineer.

When is it not suitable?

It needs a sound, stable substrate and can’t be applied below +5 °C. Active leaks are stopped first. Where the structure isn’t suitable, the surveyor will recommend another system.

Is it guaranteed?

Yes. It is installed only by Renlon Approved Installers, with our own 10-year guarantee on qualifying works.

For architects and engineersSpecifying RenStrength?Get the technical pack: TIS No. 11, data sheets C1–C4 and the variation guide.